Por favor, use este identificador para citar o enlazar este ítem: https://repositorio.uta.edu.ec/jspui/handle/123456789/29635
Título : Diseño y construcción de un prototipo de turbina Wells para la generación de energía
Autor : Mayorga Pardo, Alex Santiago
Villacrés Santamaría, Andrés Ricardo
Palabras clave : TURBINA WELLS
GENERACIÓN DE ENERGÍA
TURBOMÁQUINAS
SISTEMAS OWC
RODETE
PERFIL ALAR
TURBINAS DE REACCIÓN
Fecha de publicación : 2019
Editorial : Universidad Técnica de Ambato. Facultad de Ingeniería Civil y Mecánica, Carrera de Ingeniería Mecánica
Resumen : The present project was based on the design and construction of a Wells turbine prototype for the generation of energy, for which first we proceeded to the collection of information, to the investigation of the characteristics of the Wells turbine, to the study of the operation adequate and the parameters necessary for the design of the prototype having as research sources scientific articles and research journals. Thanks to the AirfoilTools program it was possible to proceed with the choice of the most suitable wing profile for this type of turbines, such as the NACA 0018 symmetric profile, and also for the parameters of the aerodynamic design of the wing, it was calculated with the help of theses and scientific articles. the calculations of the choice of the turbine shaft were made with the help of Shigley's book and an axis of ¼ inch in diameter was obtained. FAG catalogs were used to select the bearings In the part of the construction, the Wells turbine prototype was sent to print in a lighter material such as the PLA, the shaft was made of steel, the tube where the turbine was 8 inches diameter PVC. In the electrical part, 2 ½-inch solenoid valves, ½-inch fittings, 6 meters of ½-inch hose, 2 contactors, 2 push-buttons, one normally open and the other normally closed, a 12-V battery were purchased and a bank was made wood tests. Finally the tests were carried out in the laboratory of the Faculty of Civil and Mechanical Engineering of the Mechanical Career, maximum results were obtained: pressure of 120 Psi, speed of 6.7m /s, voltage of 14 V and 1300 rpm.
Descripción : El presente proyecto se basó en el diseño y construcción de un prototipo de una turbina Wells para la generación de energía, para lo cual primero se procedió a la recopilación de información, a la investigación de las características de la turbina Wells, al estudio del funcionamiento adecuado y a los parámetros necesarios para el diseño del prototipo teniendo como fuentes de investigación artículos científicos y revistas de investigación. Gracias al programa Airfoil Tools se pudo proceder a la elección del perfil más adecuado para este tipo de turbinas tal como el NACA 0018, también para los parámetros del diseño aerodinámico del alabe se calculó con la ayuda de tesis y de artículos científicos, los cálculos de la elección del eje de la turbina se realizaron con la ayuda del libro de Shigley y se obtuvo un eje de ¼ de pulgada de diámetro. Para la selección de los rodamientos se utilizó los catálogos FAG. En la parte de la construcción, el prototipo de la turbina Wells se mandó a imprimir en un material más liviano como es el PLA, el eje fue de acero, el tubo donde se encontraba la turbina fue de PVC de 8 pulgadas de diámetro. En la parte eléctrica se compró 2 electroválvulas de ½ pulgada, racores de ½ pulgada, 6 metros de manguera de ½ pulgada, 2 contactores, 2 pulsadores uno normalmente abierto y el otro normalmente cerrado, una batería de 12 V y se realizó un banco de pruebas de madera. Finalmente se realizaron las pruebas en el laboratorio de la Facultad de Ingeniería Civil y Mecánica de la Carrera de Mecánica se obtuvieron resultados máximos como: presión de 120 Psi, velocidad de 6.7m/s, voltaje de 14 V y1300 rpm.
URI : http://repositorio.uta.edu.ec/jspui/handle/123456789/29635
Aparece en las colecciones: Ingeniería Mecánica

Ficheros en este ítem:
Fichero Descripción Tamaño Formato  
Tesis I. M. 510 - Villacrés Santamaría Andrés Ricardo.pdfTESIS A TEXTO COMPLETO3,31 MBAdobe PDFVisualizar/Abrir


Los ítems de DSpace están protegidos por copyright, con todos los derechos reservados, a menos que se indique lo contrario.